Nova USA Home

Section 09 93 00 Staining and Transparent Finishing

Nova guide specification, CSI SectionFormat. Answer the project questions and the spec rewrites itself: options resolve, unused species drop out, and fire, coastal and warranty requirements follow your choices. Click any [bracket] to choose by hand.

SECTION 09 93 00

STAINING AND TRANSPARENT FINISHING

SPECIFIER NOTEThis guide specification is written in CSI SectionFormat and PageFormat for editing by the design professional. Specifier notes (shaded) and bracketed options [ ]✕ must be edited or deleted before issue. Highlighted items [...]✕ are manufacturer data to be confirmed by Nova USA Wood Products before this document is published.
SPECIFIER NOTEThis section is based on products of Nova USA Wood Products, 3821 24th Avenue, Forest Grove, OR 97116. Tel: (503) 419-6407. Email: sales@novausawood.com. Web: www.novausawood.com. BIM files for rainscreen, decking and clip profiles, profile drawings, installation guides and warranties are at www.novausawood.com/downloads. Technical support, samples and AIA continuing education presentations are available from the manufacturer.
SPECIFIER NOTEThis section covers field application of Nova ExoShield penetrating tung oil finish and ExoWax end-grain sealer on exterior and interior wood. Where ExoShield is factory applied, specify it in the wood product section and use this section for touch-up and maintenance coats.

PART 1 - GENERAL

1.1SUMMARY
A.Section Includes:
1.Penetrating oil finish on new wood decking, siding, trim, soffits, ceilings and site furnishings.
2.[Preparation and refinishing of existing (weathered) wood.]✕
3.End-grain sealer.
B.Related Requirements:
1.Section 06 15 00 "Modified Wood Decking" and Section 06 15 00 "Tropical Hardwood Decking and Deck Tiles."
2.Section 06 20 13 "Exterior Finish Carpentry."
3.Section 06 42 00 "Wood Paneling."
4.Section 07 46 23 "Wood Siding."
1.2SUBMITTALS
A.Product Data: Product data sheet and Safety Data Sheet for each product.
B.Samples for Initial Selection: Color samples on the actual species specified, showing full range of standard colors.
C.Samples for Verification: Two samples of each color on the actual species, not less than 12 inches (305 mm) long.
D.VOC Documentation: Manufacturer's statement of VOC content.
E.Maintenance Data: Recommended cleaning and recoat schedule.
1.3QUALITY ASSURANCE
A.Applicator Qualifications: Firm experienced in applying penetrating oil finishes of similar scope.
B.Mockups: Finish not less than 50 sq. ft. (4.6 sq. m) of each species and color for approval before proceeding.
1.4DELIVERY, STORAGE, AND HANDLING
A.Deliver in manufacturer's sealed containers with labels showing product, color and batch.
B.Store at temperatures above 40 deg F (4 deg C) in a ventilated area away from ignition sources.
C.Fire Hazard: Combustible liquid and vapor. Oily rags, applicators and waste may spontaneously combust. Place used materials in sealed metal containers filled with water and remove from site daily; dispose of per authorities having jurisdiction.
1.5FIELD CONDITIONS
A.Apply only when air and surface temperatures are 45 deg F (7 deg C) or higher, surface temperature is at least 5 deg F (3 deg C) above dew point, and no rain is expected for 24 to 48 hours.
B.Do not apply in direct hot sun above 80 deg F (27 deg C) unless excess is wiped off within 10 minutes.
C.Wood shall be dry: allow 2 to 3 days of dry weather before finishing; allow not less than one week after pressure washing.

PART 2 - PRODUCTS

2.1MANUFACTURERS
SPECIFIER NOTEChoose ONE of the two options below. Option 1 (basis of design) is recommended for most public and private work: it names Nova while allowing the contractor to propose an equal under Division 01. Use Option 2 (proprietary) only where the Owner permits a sole-source specification.
A.Basis-of-Design Product: Subject to compliance with requirements, provide ExoShield penetrating tung oil finish and ExoWax end-grain sealer by Nova USA Wood Products, Forest Grove, Oregon; www.novausawood.com.
1.Comparable Products: Products of other manufacturers will be considered when they meet every performance requirement of this Section, documented by test reports from independent laboratories, and are approved by the Architect in accordance with Section 01 60 00 - Product Requirements.
2.Substitutions: Not permitted.
B.Source Limitations: Obtain each product type, including clips, fasteners, end sealer and factory finish, from a single source through one manufacturer.
2.2PENETRATING OIL FINISH
A.Product: Nova ExoShield.
B.Composition: Tung oil base with trans-oxide pigments for UV resistance and fungicide for mold and mildew resistance.
C.VOC Content: Less than 150 g/L; complies with SCAQMD and CARB limits for penetrating stains.
D.Coverage, One Coat: Hardwoods 600 to 800 sq. ft. per gallon; softwoods 250 to 450 sq. ft. per gallon; Ambara and Inari approximately 300 sq. ft. per gallon.
E.Colors: [Clear] [Natural] [Mahogany] [Walnut] [Black Walnut] [Platinum] [Antique Bronze] [Custom color to match Architect's sample].
SPECIFIER NOTEClear is recommended only for interior and fully shaded exterior locations such as soffits and porch ceilings; pigmented colors provide UV protection on exposed surfaces.
F.Sheen: Matte.
2.3END-GRAIN SEALER
A.Product: Nova ExoWax wax-emulsion end sealer, dries clear.
2.4SURFACE PREPARATION MATERIALS
A.Cleaner: Sodium percarbonate and soda ash deck cleaner.
B.Brightener: Oxalic acid wood brightener.

PART 3 - EXECUTION

3.1EXAMINATION
A.Verify that wood is clean, dry and free of grease, oil, mill glaze and contaminants, and that moisture content is within manufacturer's limits (15 percent maximum).
3.2PREPARATION
A.New Wood: Remove contaminants. Lightly sand with 60- to 100-grit abrasive where required to open the surface (lower grit for dense hardwoods). Remove sanding dust.
B.Weathered Wood: Apply cleaner with low-pressure sprayer, allow 5 to 10 minutes dwell, scrub with stiff brush, and rinse. Brighten with oxalic acid as needed. Allow 2 to 3 days to dry.
C.Pressure Washing: Only where permitted by manufacturer; 2,800 psi maximum, 45-degree tip minimum, held not closer than 4 inches (100 mm). Do not pressure wash softwoods or thermally modified wood.
3.3APPLICATION
A.Apply in accordance with "ExoShield Best Practices" (https://www.novausawood.com/PDFs/ExoShield-Best-Practices.pdf) [and "Ambara Stain Application Instructions" (https://www.novausawood.com/PDFs/Ambara-StainApplication-Instructions.pdf)]✕, current edition at time of bid (guides are revised quarterly).
B.Stir thoroughly before and periodically during use. Apply one coat by brush, microfiber roller, pad or spray, working a few boards at a time along their full length.
C.Wipe off all excess not absorbed within 10 to 30 minutes with lint-free cloth. Do not allow finish to pool or form a film.
D.Apply ExoWax to all end grain and field cuts.
E.Keep traffic off finished surfaces for 48 hours. Full cure: up to 30 days.
3.4CLEANING AND PROTECTION
A.Protect adjacent surfaces and landscape from overspray and drips. Dispose of oily waste as specified.
B.Provide Owner with recommended maintenance schedule: recoat ExoShield on decking annually and on siding every 3 to 5 years, depending on exposure.

END OF SECTION